(R) ispLSI 2128E In-System Programmable SuperFASTTM High Density PLD Functional Block Diagram * HIGH PERFORMANCE E CMOS TECHNOLOGY -- fmax = 180 MHz Maximum Operating Frequency -- tpd = 5.0 ns Propagation Delay -- TTL Compatible Inputs and Outputs -- 5V Programmable Logic Core -- ispJTAGTM In-System Programmable via IEEE 1149.1 (JTAG) Test Access Port -- User-Selectable 3.3V or 5V I/O Supports MixedVoltage Systems -- PCI Compatible Outputs -- Open-Drain Output Option -- Electrically Erasable and Reprogrammable -- Non-Volatile -- Unused Product Term Shutdown Saves Power D3 D4 D2 D1 D0 A0 C7 A1 C6 A4 A2 A3 Logic Array D Q D Q D Q D Q C5 C4 C3 GLB A5 C2 A6 C1 Global Routing Pool (GRP) A7 B0 B1 B2 B3 Output Routing Pool (ORP) B4 B5 C0 B6 B7 Output Routing Pool (ORP) D5 Output Routing Pool (ORP) (R) Output Routing Pool (ORP) D6 CLK 0 CLK 1 CLK 2 2 Output Routing Pool (ORP) D7 Output Routing Pool (ORP) * SUPERFAST HIGH DENSITY IN-SYSTEM PROGRAMMABLE LOGIC -- 6000 PLD Gates -- 128 I/O Pins, Eight Dedicated Inputs -- 128 Registers -- High Speed Global Interconnect -- Wide Input Gating for Fast Counters, State Machines, Address Decoders, etc. -- Small Logic Block Size for Random Logic -- 100% Functional/JEDEC Upward Compatible with ispLSI 2128 Devices Output Routing Pool (ORP) Features Output Routing Pool (ORP) 0139(9A)/2128 Description The ispLSI 2128E is a High Density Programmable Logic Device. The device contains 128 Registers, 128 Universal I/O pins, eight Dedicated Input pins, three Dedicated Clock Input pins, two dedicated Global OE input pins and a Global Routing Pool (GRP). The GRP provides complete interconnectivity between all of these elements. The ispLSI 2128E features 5V in-system programmability and in-system diagnostic capabilities. The ispLSI 2128E offers non-volatile reprogrammability of all logic, as well as the interconnect to provide truly reconfigurable systems. * ispLSI OFFERS THE FOLLOWING ADDED FEATURES -- Increased Manufacturing Yields, Reduced Time-toMarket and Improved Product Quality -- Reprogram Soldered Devices for Faster Prototyping * OFFERS THE EASE OF USE AND FAST SYSTEM SPEED OF PLDs WITH THE DENSITY AND FLEXIBILITY OF FIELD PROGRAMMABLE GATE ARRAYS -- Complete Programmable Device Can Combine Glue Logic and Structured Designs -- Enhanced Pin Locking Capability -- Three Dedicated Clock Input Pins -- Synchronous and Asynchronous Clocks -- Programmable Output Slew Rate Control to Minimize Switching Noise -- Flexible Pin Placement -- Optimized Global Routing Pool Provides Global Interconnectivity The basic unit of logic on the ispLSI 2128E device is the Generic Logic Block (GLB). The GLBs are labeled A0, A1 .. D7 (see Figure 1). There are a total of 32 GLBs in the ispLSI 2128E device. Each GLB is made up of four macrocells. Each GLB has 18 inputs, a programmable AND/OR/Exclusive OR array, and four outputs which can be configured to be either combinatorial or registered.Inputs to the GLB come from the GRP and dedicated inputs. All of the GLB outputs are brought back into the GRP so that they can be connected to the inputs of any GLB on the device. The device also has 128 I/O cells, each of which is directly connected to an I/O pin. Each I/O cell can be Copyright (c) 2002 Lattice Semiconductor Corp. All brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. LATTICE SEMICONDUCTOR CORP., 5555 Northeast Moore Ct., Hillsboro, Oregon 97124, U.S.A. Tel. (503) 268-8000; 1-800-LATTICE; FAX (503) 268-8556; http://www.latticesemi.com 2128e_03 1 January 2002 Specifications ispLSI 2128E Functional Block Diagram TDI/IN 7 TDO/IN 6 I/O 99 I/O 98 I/O 97 I/O 96 I/O 103 I/O 102 I/O 101 I/O 100 I/O 107 I/O 106 I/O 105 I/O 104 I/O 111 I/O 110 I/O 109 I/O 108 I/O 115 I/O 114 I/O 113 I/O 112 I/O 119 I/O 118 I/O 117 I/O 116 I/O 123 I/O 122 I/O 121 I/O 120 I/O 127 I/O 126 I/O 125 I/O 124 Figure 1. ispLSI 2128E Functional Block Diagram RESET Input Bus GOE 0 GOE 1 Output Routing Pool (ORP) Output Routing Pool (ORP) Megablock Generic Logic Blocks (GLBs) D7 D6 D5 D4 D2 D3 IN 5 IN 4 D0 D1 I/O 95 I/O 94 I/O 93 I/O 92 A0 I/O 8 I/O 9 I/O 10 I/O 11 I/O 20 I/O 21 I/O 22 I/O 23 I/O 24 I/O 25 I/O 26 I/O 27 I/O 28 I/O 29 I/O 30 I/O 31 I/O 87 I/O 86 I/O 85 I/O 84 A2 C4 Global Routing Pool (GRP) Input Bus I/O 16 I/O 17 I/O 18 I/O 19 C5 A3 C3 A4 Output Routing Pool (ORP) I/O 12 I/O 13 I/O 14 I/O 15 A1 C2 A5 C1 I/O 83 I/O 82 I/O 81 I/O 80 I/O 79 I/O 78 I/O 77 I/O 76 I/O 75 I/O 74 I/O 73 I/O 72 I/O 71 I/O 70 I/O 69 I/O 68 I/O 67 I/O 66 I/O 65 I/O 64 A6 C0 A7 TCK/ IN 0 TMS/IN 1 B0 B1 B2 B3 B5 B4 Output Routing Pool (ORP) B7 B6 Output Routing Pool (ORP) CLK 0 CLK 1 CLK 2 I/O 4 I/O 5 I/O 6 I/O 7 I/O 91 I/O 90 I/O 89 I/O 88 Input Bus Output Routing Pool (ORP) C6 Output Routing Pool (ORP) I/O 0 I/O 1 I/O 2 I/O 3 Output Routing Pool (ORP) C7 Input Bus individually programmed to be a combinatorial input, output or bi-directional I/O pin with 3-state control. The signal levels are TTL compatible voltages and the output drivers can source 4 mA or sink 8 mA. Each output can be programmed independently for fast or slow output slew rate to minimize overall output switching noise. By connecting the VCCIO pins to a common 5V or 3.3V power supply, I/O output levels can be matched to 5V or 3.3V compatible voltages. When connected to a 5V supply, the I/O pins provide PCI-compatible output drive. Y0 Y1 Y2 I/O 60 I/O 61 I/O 62 I/O 63 I/O 56 I/O 57 I/O 58 I/O 59 I/O 52 I/O 53 I/O 54 I/O 55 I/O 48 I/O 49 I/O 50 I/O 51 I/O 44 I/O 45 I/O 46 I/O 47 I/O 40 I/O 41 I/O 42 I/O 43 I/O 36 I/O 37 I/O 38 I/O 39 I/O 32 I/O 33 I/O 34 I/O 35 IN 2 IN 3 BSCAN 0139/2128E Clocks in the ispLSI 2128E device are selected using the dedicated clock pins. Three dedicated clock pins (Y0, Y1, Y2) or an asynchronous clock can be selected on a GLB basis. The asynchronous or Product Term clock can be generated in any GLB for its own clock. Programmable Open-Drain Outputs In addition to the standard output configuration, the outputs of the ispLSI 2128E are individually programmable, either as a standard totem-pole output or an open-drain output. The totem-pole output drives the specified Voh and Vol levels, whereas the open-drain output drives only the specified Vol. The Voh level on the open-drain output depends on the external loading and pull-up. This output configuration is controlled by a programmable fuse. The default configuration when the device is in bulk erased state is totem-pole configuration. The open-drain/totem-pole option is selectable through the Lattice software tools. Eight GLBs, 32 I/O cells, two dedicated inputs and two ORPs are connected together to make a Megablock (see Figure 1). The outputs of the eight GLBs are connected to a set of 32 universal I/O cells by the two ORPs. Each ispLSI 2128E device contains four Megablocks. The GRP has as its inputs, the outputs from all of the GLBs and all of the inputs from the bi-directional I/O cells. All of these signals are made available to the inputs of the GLBs. Delays through the GRP have been equalized to minimize timing skew. 2 Specifications ispLSI 2128E Absolute Maximum Ratings 1 Supply Voltage Vcc .................................. -0.5 to +7.0V Input Voltage Applied ........................ -2.5 to VCC +1.0V Off-State Output Voltage Applied ..... -2.5 to VCC +1.0V Storage Temperature ................................ -65 to 150C Case Temp. with Power Applied .............. -55 to 125C Max. Junction Temp. (TJ) with Power Applied ... 150C 1. Stresses above those listed under the "Absolute Maximum Ratings" may cause permanent damage to the device. Functional operation of the device at these or at any other conditions above those indicated in the operational sections of this specification is not implied (while programming, follow the programming specifications). DC Recommended Operating Condition MIN. MAX. UNITS 4.75 5.25 V 5V 4.75 5.25 V 3.3V 3.0 3.6 V V PARAMETER SYMBOL VCC Supply Voltage: Logic Core, Input Buffers VCCIO Supply Voltage: Output Drivers VIL VIH Input Low Voltage 0 0.8 Input High Voltage 2.0 Vcc+1 TA = 0C to +70C V Table 2-0005/2128E Capacitance (TA=25C, f=1.0 MHz) SYMBOL C1 C2 C3 TYP UNITS Dedicated Input Capacitance PARAMETER 8 pf VCC = 5.0V, VIN = 2.0V TEST CONDITIONS I/O Capacitance 8 pf VCC = 5.0V, VI/O = 2.0V Clock Capacitance 10 pf VCC = 5.0V, VY = 2.0V Table 2-0006/2128E Erase/Reprogram Specification PARAMETER Erase/Reprogram Cycles MINIMUM MAXIMUM UNITS 10,000 - Cycles Table 2-0008/2128E 3 Specifications ispLSI 2128E Switching Test Conditions GND to 3.0V Input Pulse Levels Figure 2. Test Load 1.5 ns Input Rise and Fall Time 10% to 90% Input Timing Reference Levels 1.5V Output Timing Reference Levels 1.5V Output Load + 5V See Figure 2 R1 Table 2-0003/2128E 3-state levels are measured 0.5V from steady-state active level. Device Output Output Load Conditions (see Figure 2) TEST CONDITION A B C R1 R2 CL 470 390 35pF Active High 390 35pF Active Low 470 390 35pF Active High to Z at VOH -0.5V 390 5pF Active Low to Z at VOL +0.5V 470 390 5pF Test Point C L* R2 *CL includes Test Fixture and Probe Capacitance. 0213A Table 2 - 0004A/2000 DC Electrical Characteristics Over Recommended Operating Conditions SYMBOL CONDITION PARAMETER MIN. TYP.3 MAX. UNITS VOL VOH IIL Output Low Voltage IOL = 8 mA - - Output High Voltage IOH = -4 mA 2.4 - - V Input or I/O Low Leakage Current 0V VIN VIL (Max.) - - -10 A IIH Input or I/O High Leakage Current (VCCIO - 0.2)V VIN VCCIO - - 10 A VCCIO VIN 5.25V - - 10 A IIL-PU IOS1 I/O Active Pull-Up Current 0V VIN 2.0V -10 - -250 A Output Short Circuit Current VCCIO = 5.0V or 3.3V, VOUT = 0.5V - - -240 mA ICC3,4 Operating Power Supply Current VIL = 0.0V, VIH = 3.0V fTOGGLE = 1 MHz - 165 - mA 0.4 V Table 2-0007/2128E 1. One output at a time for a maximum duration of one second. VOUT = 0.5V was selected to avoid test problems by tester ground degradation. Characterized but not 100% tested. 2. Meaured using eight 16-bit counters. 3. Typical values are at VCC = 5V and TA = 25C. 4. Unused inputs held at 0.0V. 5. Maximum ICC varies widely with specific device configuration and operating frequency. Refer to the Power Consumption section of this data sheet and the Thermal Management section of the Lattice Semiconductor Data Book or CD-ROM to estimate maximum ICC. 4 Specifications ispLSI 2128E External Timing Parameters Over Recommended Operating Conditions PARAMETER tpd1 tpd2 fmax fmax (Ext.) fmax (Tog.) tsu1 tco1 th1 tsu2 tco2 th2 tr1 trw1 tptoeen tptoedis tgoeen tgoedis twh twl 1. 2. 3. 4. TEST 2 4 # COND. -135 -180 DESCRIPTION1 -100 MIN. MAX. MIN. MAX. MIN. MAX. UNITS A 1 Data Prop Delay, 4PT Bypass, ORP Bypass - 5.0 - 7.5 - 10.0 ns A 2 Data Prop Delay - 7.5 - 10.0 - 13.0 ns A 3 Clk Freq with Internal Feedback3 180 - 135 - 100 - MHz 125 - 100 - 77.0 - MHz 1 tsu2 + tco1 - 4 Clk Freq with External Feedback ( ) - 5 Clk Frequency, Max. Toggle 200 - 143 - 100 - MHz - 6 GLB Reg Setup Time before Clk, 4 PT Bypass 4.0 - 5.0 - 6.5 - ns A 7 GLB Reg Clk to Output Delay, ORP Bypass - 3.0 - 4.0 - 5.0 ns - 8 GLB Reg Hold Time after Clk, 4 PT Bypass 0.0 - 0.0 - 0.0 - ns - 9 GLB Reg Setup Time before Clk 5.0 - 6.0 - 8.0 - ns - 10 GLB Reg Clk to Output Delay - 3.5 - 4.5 - 6.0 ns - 11 GLB Reg Hold Time after Clk 0.0 - 0.0 - 0.0 - ns A 12 External Reset Pin to Output Delay - 7.0 - 10.0 - 13.5 ns - 13 External Reset Pulse Duration 4.0 - 5.0 - 6.5 - ns B 14 Input to Output Enable - 10.0 - 12.0 - 15.0 ns C 15 Input to Output Disable - 10.0 - 12.0 - 15.0 ns B 16 Global OE Output Enable - 5.0 - 7.0 - 9.0 ns C 17 Global OE Output Disable - 5.0 - 7.0 - 9.0 ns - 18 External Synch Clk Pulse Duration, High 2.5 - 3.5 - 5.0 - ns - 19 External Synch Clk Pulse Duration, Low 2.5 - 3.5 - 5.0 - ns Unless noted otherwise, all parameters use a GRP load of four GLBs, 20 PTXOR path, ORP and Y0 clock. Refer to Timing Model in this data sheet for further details. Standard 16-bit counter using GRP feedback. Reference Switching Test Conditions section. 5 Table 2-0030A/2128E Specifications ispLSI 2128E Internal Timing Parameters1 Over Recommended Operating Conditions PARAMETER 2 # -180 DESCRIPTION -100 -135 MIN. MAX. MIN. MAX. MIN. MAX. UNITS Inputs tio tdin 20 Input Buffer Delay - 0.5 - 0.5 - 0.5 ns 21 Dedicated Input Delay - 1.1 - 1.7 - 2.2 ns 22 GRP Delay - 0.6 - 1.2 - 1.7 ns 23 4 Product Term Bypass Path Delay (Combinatorial) - 1.9 - 3.7 - 5.8 ns 4.2 - 5.8 ns 6.8 ns GRP tgrp GLB t4ptbpc t4ptbpr t1ptxor t20ptxor txoradj tgbp tgsu tgh tgco tgro tptre tptoe tptck 24 4 Product Term Bypass Path Delay (Registered) - 2.9 - 25 1 Product Term/XOR Path Delay - 3.9 - 5.2 - 26 20 Product Term/XOR Path Delay - 3.9 - 5.2 - 7.3 ns 27 XOR Adjacent Path Delay 3 - 3.9 - 5.2 - 8.0 ns 28 GLB Register Bypass Delay - 0.0 - 0.5 - 0.5 ns - ns 29 GLB Register Setup Time before Clock 0.7 - 0.7 - 1.2 30 GLB Register Hold Time after Clock 3.3 - 4.3 - 4.0 - ns 31 GLB Register Clock to Output Delay - 0.3 - 0.3 - 0.3 ns 32 GLB Register Reset to Output Delay - 0.6 - 1.1 - 1.3 ns 6.1 ns 33 GLB Product Term Reset to Register Delay - 4.8 - 6.0 - 34 GLB Product Term Output Enable to I/O Cell Delay - 5.9 - 6.9 - 8.6 ns 1.0 4.0 2.5 5.5 4.1 7.1 ns 36 ORP Delay - 0.9 - 1.0 - 1.4 ns 37 ORP Bypass Delay - 0.4 - 0.5 - 0.4 ns 38 Output Buffer Delay - 1.6 - 1.6 - 1.6 ns 39 Output Slew Limited Delay Adder - 1.5 - 1.5 - 10.0 ns 40 I/O Cell OE to Output Enabled - 3.0 - 3.4 - 4.2 ns 41 I/O Cell OE to Output Disabled - 3.0 - 3.4 - 4.2 ns 4.8 ns 35 GLB Product Term Clock Delay ORP torp torpbp Outputs tob tsl toen todis tgoe - 2.0 - 3.6 - 43 Clock Delay, Y0 to Global GLB Clock Line (Ref. clock) 0.7 0.7 1.6 1.6 2.7 2.7 ns 44 Clock Delay, Y1 or Y2 to Global GLB Clock Line 0.9 0.9 1.8 1.8 2.7 2.7 ns - 4.4 - 6.3 - 9.2 ns 42 Global Output Enable Clocks tgy0 tgy1/2 Global Reset tgr 45 Global Reset to GLB 1. Internal Timing Parameters are not tested and are for reference only. 2. Refer to Timing Model in this data sheet for further details. 3. The XOR adjacent path can only be used by hard macros. 6 Table 2-0036A/2128E Specifications ispLSI 2128E ispLSI 2128E Timing Model I/O Cell GRP GLB ORP I/O Cell Feedback Ded. In I/O Pin (Input) Comb 4 PT Bypass #23 #21 I/O Delay GRP Reg 4 PT Bypass GLB Reg Bypass ORP Bypass #20 #22 #24 #28 #37 20 PT XOR Delays GLB Reg Delay ORP Delay #25 - 27 D Q #38, #39 #36 RST #45 Reset #29 - 32 Control RE PTs OE #33 - 35 CK Y0,1,2 GOE0, 1 #40, 41 #43, 44 #42 0491/2128E Derivations of tsu, th and tco from the Product Term Clock tsu = = = 3.6 = Logic + Reg su - Clock (min) (tio + tgrp + t20ptxor) + (tgsu) - (tio + tgrp + tptck(min)) (#20 + #22 + #26) + (#29) - (#20 + #22 + #35) (0.5 + 0.6 + 3.9) + (0.7) - (0.5 + 0.6 + 1.0) th = = = 3.4 = Clock (max) + Reg h - Logic (tio + tgrp + tptck(max)) + (tgh) - (tio + tgrp + t20ptxor) (#20 + #22 + #35) + (#30) - (#20 + #22 + #26) (0.5 + 0.6 + 4.0) + (3.3) - (0.5 + 0.6 + 3.9) tco = = = 7.9 = Clock (max) + Reg co + Output (tio + tgrp + tptck(max)) + (tgco) + (torp + tob) (#20 + #22 + #35) + (#31) + (#36 + #38) (0.5 + 0.6 + 4.0) + (0.3) + (0.9 + 0.6) Table 2-0042/2128E Note: Calculations are based upon timing specifications for the ispLSI 2128E-180L. 7 I/O Pin (Output) Specifications ispLSI 2128E Power Consumption Figure 3 shows the relationship between power and operating speed. Power consumption in the ispLSI 2128E device depends on two primary factors: the speed at which the device is operating and the number of Product Terms used. Figure 3. Typical Device Power Consumption vs fmax 500 ispLSI 2128E 450 ICC (mA) 400 350 300 250 200 150 100 0 20 40 60 80 100 120 140 160 180 fmax (MHz) Notes: Configuration of eight 16-bit counters Typical current at 5V, 25 C ICC can be estimated for the ispLSI 2128E using the following equation: ICC = 27 + (# of PTs * 0.55) + (# of nets * max freq * 0.0058) Where: # of PTs = Number of Product Terms used in design # of nets = Number of Signals used in device Max freq = Highest Clock Frequency to the device (in MHz) The ICC estimate is based on typical conditions (VCC = 5.0V, room temperature) and an assumption of two GLB loads on average exists. These values are for estimates only. Since the value of ICC is sensitive to operating conditions and the program in the device, the actual ICC should be verified. 0127/2128E 8 Specifications ispLSI 2128E Pin Description NAME TQFP PIN NUMBERS 27, 35, 41, 46, 52, 59, 65, 71, 77, 83, 90, 95, 102, 116, 124, 130, 135, 141, 148, 154, 160, 167, 173, 3, 8, 16, IN 2 - IN 5 106, 107, 112, 113 Dedicated input pins to the device. GOE 0, GOE 1 110, 109, Global Output Enable input pins. RESET 22 Active Low (0) Reset pin which resets all of the GLB registers in the device. Y0, Y1, Y2 19, 21, 111 Dedicated Clock inputs. These clock inputs are connected to one of the clock inputs of all the GLBs on the device. BSCAN 23 Input - Dedicated in-system programming enable input pin. This pin is brought low to enable the programming mode. The TMS, TDI, TDO and TCK options become active. TDI/IN 71 24 Input - This pin performs two functions. When BSCAN is logic low, it functions as an input pin to load programming data into the device. SDI is also used as one of the two control pins for the ISP state machine. When BSCAN is high, it functions as a dedicated input pin. TCK/IN 01 25 Input - This pin performs two functions. When BSCAN is logic low, it functions as a clock pin for the Serial Shift Register. When BSCAN is high, it functions as a dedicated input pin. TMS/IN 11 26 Input - This pin performs two functions. When BSCAN is logic low, it functions as pin to control the operation of the programming state machine. When BSCAN is high, it functions as a dedicated input pin. TDO/IN 61 114 Output/Input - This pin performs two functions. When BSCAN is logic low, it functions as the pin to read the isp data. When BSCAN is high, it functions as a dedicated input pin. GND 1, 64, 117, 172 13, 122, 10, 118, VCC VCCIO NC 28, 36, 42, 47, 53, 60, 66, 72, 79, 85, 91, 96, 103, 119, 125, 131, 136, 143, 149, 155, 161, 168, 174, 4, 9, 17, DESCRIPTION I/O 0 - I/O 4 I/O 5 - I/O 9 I/O 10 - I/O 14 I/O 15 - I/O 19 I/O 20 - I/O 24 I/O 25 - I/O 29 I/O 30 - I/O 34 I/O 35 - I/O 39 I/O 40 - I/O 44 I/O 45 - I/O 49 I/O 50 - I/O 54 I/O 55 - I/O 59 I/O 60 - I/O 64 I/O 65 - I/O 69 I/O 70 - I/O 74 I/O 75 - I/O 79 I/O 80 - I/O 84 I/O 85 - I/O 89 I/O 90 - I/O 94 I/O 95 - I/O 99 I/O 100 - I/O 104 I/O 105 - I/O 109 I/O 110 - I/O 114 I/O 115 - I/O 119 I/O 120 - I/O 124 I/O 125 - I/O 127 31, 37, 43, 48, 55, 61, 67, 73, 80, 86, 92, 97, 104, 120, 126, 132, 138, 145, 150, 156, 163, 169, 175, 5, 12, 18 32, 38, 44, 50, 57, 62, 68, 75, 81, 87, 93, 99, 105, 121, 127, 133, 139, 146, 151, 158, 164, 170, 176, 6, 14, 33, Input/Output Pins - These are the general purpose I/O pins used by the logic array. 39, 45, 51, 58, 63, 70, 76, 82, 88, 94, 101, 115, 123, 129, 134, 140, 147, 153, 159, 165, 171, 2, 7, 15, 11, 29, 40, 49, Ground (GND) 69, 84, 89, 108, 128, 137, 152, 157, 34, 144, 30, 142, 56, 78, 166 54, 74, 162 20 100, VCC 98, Supply voltage for output drivers, 5V or 3.3V. All VCCIO pins must be connected to the same voltage level. No Connect Table 2-0002/2128E 1. Pins have dual function capability. 9 Specifications ispLSI 2128E Pin Configuration 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 I/O 113 I/O 112 I/O 111 I/O 110 GND I/O 109 I/O 108 I/O 107 I/O 106 I/O 105 VCC I/O 104 I/O 103 I/O 102 VCCIO I/O 101 I/O 100 I/O 99 I/O 98 GND I/O 97 I/O 96 I/O 95 I/O 94 GND I/O 93 I/O 92 I/O 91 I/O 90 I/O 89 I/O 88 I/O 87 VCC I/O 86 VCCIO I/O 85 I/O 84 I/O 83 I/O 82 GND I/O 81 I/O 80 I/O 79 I/O 78 ispLSI 2128E 176-Pin TQFP Pinout Diagram ispLSI 2128E Top View 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 I/O 77 I/O 76 I/O 75 I/O 74 GND I/O 73 I/O 72 I/O 71 I/O 70 I/O 69 VCC I/O 68 I/O 67 I/O 66 VCCIO GND I/O 65 I/O 64 TDO/IN 62 IN 5 IN 4 Y2 GOE 0 GOE 1 GND IN 3 IN 2 I/O 63 I/O 62 I/O 61 I/O 60 I/O 59 VCC I/O 58 VCCIO I/O 57 I/O 56 I/O 55 I/O 54 I/O 53 I/O 52 I/O 51 I/O 50 GND 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 I/O 14 I/O 15 I/O 16 I/O 17 GND I/O 18 I/O 19 I/O 20 I/O 21 VCCIO I/O 22 VCC I/O 23 I/O 24 I/O 25 I/O 26 I/O 27 I/O 28 I/O 29 GND I/O 30 I/O 31 I/O 32 I/O 33 GND I/O 34 I/O 35 I/O 36 I/O 37 VCCIO I/O 38 I/O 39 I/O 40 VCC I/O 41 I/O 42 I/O 43 I/O 44 I/O 45 GND I/O 46 I/O 47 I/O 48 I/O 49 GND I/O 114 I/O 115 I/O 116 I/O 117 I/O 118 I/O 119 I/O 120 I/O 121 VCCIO GND I/O 122 VCC I/O 123 I/O 124 I/O 125 I/O 126 I/O 127 Y0 1 NC Y1 RESET BSCAN 2TDI/IN 7 2TCK/IN 0 2 TMS/IN 1 I/O 0 I/O 1 GND VCCIO I/O 2 I/O 3 I/O 4 VCC I/O 5 I/O 6 I/O 7 I/O 8 I/O 9 GND I/O 10 I/O 11 I/O 12 I/O 13 176-TQFP/2128E 1. NC pins are not to be connected to any active signals, VCC or GND. 2. Pins have dual function capability. 10 Specifications ispLSI 2128E Part Number Description ispLSI 2128E - XXX X XXXX X Device Family Grade Blank = Commercial Device Number Package T176 = TQFP Speed 180 = 180 MHz fmax 135 = 135 MHz fmax 100 = 100 MHz fmax Power L = Low 0212/2128E ispLSI 2128E Ordering Information FAMILY ispLSI fmax (MHz) tpd (ns) ORDERING NUMBER PACKAGE 180 5.0 ispLSI 2128E-180LT176 176-Pin TQFP 135 7.5 ispLSI 2128E-135LT176 176-Pin TQFP 100 10.0 ispLSI 2128E-100LT176 176-Pin TQFP Table 2-0041/2128E 11